An sis unilateral finline mixer with an ultra-wide if bandwidth
21st International Symposium on Space Terahertz Technology 2010, ISSTT 2010 (2010) 179-183
Abstract:
In this paper, we will present the design and the simulation of a 230GHz finline Ultra-wide IF Bandwidth SIS mixer. This mixer will be used in a novel millimeter-wave heterodyne interferometer: GUBBINS. GUBBINS is designed to demonstrate high surface brightness mm-wave interferometry at modest spatial and spectrum resolution. Its observational targets are the spectrum of the Sunyaev-Zel'dovich effect in the brightness galaxy cluster[3]. The archetype of the mixer design described here is an antipodal finline SIS mixer designed by Paul Grimes in Oxford Experimental Cosmology group in 2008[1]. Here several improvement and modification are made to simplify the design and fabrication, and also enhance the IF bandwidth. An unilateral finline replaces the complicated antipodal finline. No RF bandpass filter is needed after finline. The tuning circuit design presented here aims to achieve wider RF coupling bandwidth, even though only a single junction is used. A multi-stage IF transformer follows the IF bonding pad matching the IF output of the mixer to the input of the IF amplifier, as well as reducing the impact of the parasitical capacitance introduced by the RF finline and RF radial stub.Measured performance of a 230 GHz prototype focal-plane feedhorn array made by direct drilling of smooth-walled horns
21st International Symposium on Space Terahertz Technology 2010, ISSTT 2010 (2010) 91-96
Abstract:
We present the first, complete 230 GHz feedhorn array manufactured by direct drilling of smooth-walled horns into a single plate of aluminium. The horn design process, based on a genetic algorithm, is described and the fabrication process, via direct drilling using shaped drill bits, is presented. We present cross coupling and beam pattern measurements of a close-packed pair of the smooth-walled horns fabricated in a single block of aluminium. We also present a prototype 37 horn array, again fabricated by drilling into a single block. Our measurements show that our designs and fabrication techniques will be robust when applied to large focal arrays of horns consisting of hundreds or thousands of feedhorns. We expect our smooth-walled horn designs and novel manufacturing techniques will offer an attractive, low-cost alternate to traditional horn arrays consisting of electroformed corrugated horns.A 700 GHz unilateral finline SIS mixer fed by a multi-flare angle smooth-walled horn
Proceedings of SPIE - The International Society for Optical Engineering 7741 (2010)
Abstract:
We present the design of a broadband superconductor-insulator- superconductor (SIS) mixer operating near 700 GHz. A key feature of our design is the utilisation of a new type of waveguide to planar circuit transition comprising a unilateral finline taper. This transition is markedly easier to design, simulate and fabricate than the antipodal finline we employed previously. The finline taper and the superconducting circuitry are deposited on a 15 μm thick silicon substrate. The employment of the very thin substrate, achieved using Silicon-On-Insulator (SOI) technology, makes it easy to match the incoming signal to the loaded waveguide. The lightweight mixer chip is held in the E-plane of the waveguide using gold beam leads, avoiding the need for deep grooves in the waveguide wall. This new design yields a significantly shorter chip, free of serrations and a wider RF bandwidth. Since tuning and all other circuits are integrated on the mixer chip, the mixer block is extremely simple, comprising a feed horn and a waveguide section without any complicated mechanical features. We employ a new type of smooth-walled horn which exhibits excellent beam circularity and low cross polarisation, comparable to the conventional corrugated horn, and yet is easier to fabricate. The horn is machined by standard milling with a drill tool shaped into the horn profile. In this paper, we describe the detailed design of the mixer chip including electromagnetic simulations, and the mixer performance obtained with SuperMix simulations. We also present the preliminary measurements of the smooth-walled horn radiation patterns near the mixer operating frequencies. © 2010 SPIE.A CO(3-2) survey of a merging sequence of luminous infrared galaxies
Monthly Notices of the Royal Astronomical Society 406:2 (2010) 1364-1378
Abstract:
Luminous infrared galaxies (LIR > 1011 L⊙) are often associated with interacting galactic systems and are thought to be powered by merger-induced starbursts and/or dust-enshrouded active galactic nucleus. In such systems, the evolution of the dense, star-forming molecular gas as a function of merger separation is of particular interest. Here, we present observations of the CO(3-2) emission from a sample of luminous infrared galaxy mergers that span a range of galaxy-galaxy separations. The excitation of the molecular gas is studied by examining the CO(3-2)/CO(1-0) line ratio, r31, as a function of merger extent. We find these line ratios, r31, to be consistent with kinetic temperatures of Tk = (30-50) K and gas densities of We also find weak correlations between r31 and both merger progression and star formation efficiency [LFIR/LCO(1-0)]. These correlations show a tendency for gas excitation to increase as the merger progresses and the star formation efficiency rises. To conclude, we calculate the contributions of the CO(3-2) line to the 850-μm fluxes measured with SCUBA (Submillimetre Common-User Bolometer Array), which are seen to be significant (∼22 per cent). © 2010 The Authors. Journal compilation © 2010 RAS.The JCMT Nearby Galaxies Legacy Survey - III. Comparisons of cold dust, polycyclic aromatic hydrocarbons, molecular gas and atomic gas in NGC 2403
Monthly Notices of the Royal Astronomical Society 402:3 (2010) 1409-1425